Fullcover Tips in Gel : advice and clarifications

A true innovation, a system that is revolutionizing the world of nails.
The Fullcover it's a tip whole that blends with the natural nail through the use with Base Rubber or Acrylgel, making it a single, resistant yet flexible body.

All the tip They are produced with an injection molding process, but the quality of the production materials varies.
Each manufacturer uses different types of plastic for their tip.
We at Nailfor We have chosen only pure virgin ABS plastic of the highest quality.

The result is a tip resistant, malleable and long-lasting which provides a valid alternative to reconstruction, while remaining a system soak off if used in combination with the Base Rubber.

Fullcover Tips IN Gel: application tips step by step

- THIN CUTICLE AREA:
Thin, tapered contact area for surface conformity; designed to blend seamlessly into the natural nail after application with the gel; It is however recommended to slightly lower the step with a small cylinder of medium-grained cardboard or with a diamond tip to make it perfectly similar to a natural nail.

- REINFORCED STRESS AREA:
Reinforced apex sides and extension edge to protect the tips from impact cracks and fissures.
Perfect side and already defined shape.
Depending on the chosen shape, the application will be sufficient to obtain a defined work, a slight reinforcement in the upper part without altering the architecture already perfect and uniform to the natural nail; it is sufficient to mattify with a buffer the surface and apply a light base coat before applying the paint and sealant.

 - ALL THE Tip THEY WORK BETTER IF:

• They are made of high quality virgin plastic
• The choice was made tip just right to create the right kind of "reconstruction"
• The choice was made tip of the correct size that fits the nail perfectly, without having to press down on the vertical center of the tip.

- THERE MAY BE PROBLEMS WHEN:

• Acetone is used to dull the tip;
• The contact area between the tip and the natural nail has not been well prepared;
• A choice has been made tip wrong shape or size;
• Bubbles formed during application or the bonding product did not cure properly;
• The tip it was applied crookedly.

When choosing a tip, the fact that they fit together and fit is essential for the duration of the reconstruction:

• Match - Choose the tip that perfectly matches the C-Curve type of the natural nail.
• Dressing - The tip It must fit effortlessly from side to side and incorporate the extension edge of the natural nail perfectly.

TROUBLESHOOTING:

- BUBBLES IN ADHESION:

Application tip wrong
• Make sure that the tip fit perfectly. If it is too small, the contact area will not conform properly to the natural nail and will not adhere properly. If the tip it's too big, there will be empty spaces, especially in the corners.
• Use a sufficient amount of Gel. If you use too little, there will be gaps between the natural nail and the contact area. If you use too much, the excess will run down the sides or free edge and bubbles will appear.

• Properly embrace the extension edge of the natural nail with the tip. If you don't perfectly match the tip of the extension edge of your natural nail to the stop area of the tip, this will weaken and may also trap debris, dirt and bacteria.

In case there are so-called pockets it is preferable to remove the tip and place a new one.

- SPLITS:

The tip It was thinned too much in the preparation. It was degreased with acetone.

• If acetone touches the tip they are formed micro cracks that weaken it.
• Wrong cut. Use a guillotine to tip sharpened to shorten if necessary. Using a dull blade when cutting will stress the plastic and may cause cracking.

METHOD:

Choosing the correct size of the fullcover tip
Sand the inside of the tip up to the point of exit from the free margin.

- Preparation:
Sanitize your hands

Perform the dry manicure
Buff the natural nail with a 240/240 grit file.

Remove any dust residue, clean the nail with Spray sanitizer

Apply Nail prep
Apply Primer or Primer Ultra bond

Apply a thin layer of Base Rubber, polymerize in lamp Uv Led 60''

Apply Base Rubber or Acrylgel directly on the tip
Make sure the adhesive adheres perfectly tip on the previously applied base layer, taking care not to form air bubbles.
Polymerize with mini lamp led uv a few seconds and continue polymerization under the lamp for 60''.

Lower the thickness if necessary tip in the cuticle area with a diamond tip;
To dull the surface of the tip with a buffer and apply a light base coat rubber

Apply the chosen color

Seal with Top Tempered

INFO BASIC AND SPECIALIZATION COURSES Nailfor WRITE TO:

piazzadebora116@gmail.comOr on the Facebook Group Nailfor ACADEMY:https://www.facebook.com/groups/291695182494118

Follow us on our social media Facebook And Instagram to stay up to date on the news and find demonstration videos on the applications of our products!

By clicking on the links you can review Facebook Live on the step by step application and removal and refill from the Fullcover Tips:

https://www.facebook.com/watch/337557210138129/802743523926491